NAVWEPS 16-30ARC5-501

Handbook

BENCH TEST

And

ALIGNMENT PROCEDURE

RADIO EQUIPMENT

AN/ARC-5

PUBLISHED BY DIRECTION OF THE CHIEF OF THE BUREAU OF NAVAL
WEAPONS

1 October 1949

TABLE OF CONTENTS
SECTION I INTRODUCTION
1--1. PURPOSE OF BENCH MAINTENANCE PROCEDURE.

1--4. DESCRIPTION OF PROCEDURE.
1--6. USE OF THE PROCEDURE.
1--11. GENERAL DESCRIPTION OF AN/ARC-5 EQUIPMENT.

1--14. TEST EQUIPMENT.
SECTION II PERFORMANCE CHECKS
2--1. GENERAL.
2--4. RECEIVER CHECKS.
2--9. BAND NOISE.
2--12. SENSITIVITY.
2--15. SELECTIVITY.
2--17. AVC CHARACTERISTICS.
2--21. TRANSMITTER CHECKS.
2--26. TRANSMITTER TRACKING AND LOADING.
2--29. MODULATION CHECK.
SECTION III ALIGNMENT PROCEDURE
3--1. RECEIVER ALIGNMENT.
3--6. TRANSMITTER ALIGNMENT.
SECTION IV TROUBLE ISOLATION
4--1. RADIO RECEIVER.
4--4. AUDIO-FREQUENCY CIRCUIT.
4--6. INTERMEDIATE-FREQUENCY CIRCUIT.
4--8. CONVERTER CIRCUIT. (Follow chart below).

4--10. RADIO-FREQUENCY CIRCUIT.
4--11. ANTENNA CIRCUIT.
4--12. TRANSMITTER AND MODULATOR.
4--15. OSCILLATOR.
4--16. FINAL AMPLIFIER.
4--17. MODULATOR.

Figure 1-1. AN/ARC-5 Equipment
SECTION
I INTRODUCTION
1--1.
PURPOSE OF BENCH MAINTENANCE PROCEDURE.
1--2. The basic approach used in the development of this manual has been
that of dividing all equipments into two categories:
a. Components operating
at or above a minimum standard of satisfactory performance.
b. Defective or
poorly performing components.
1--3. Bench maintenance is reduced, first, to
determining whether or not an equipment is operating satisfactorily, and,
second, repairing the equipment if it is found to be defective. This division
results in a procedure having four sections:
a. INTRODUCTION -- This section presents a brief description
of the basic function of the subject equipment, its primary power requirements,
inter-unit connecting cables, a suggested bench mock-up, and other information
necessary for quick reference with respect to proper maintenance
techniques.
b. PERFORMANCE
CHECKS -- These are of primary importance and are to be performed in sequence
upon the subject equipment. An equipment that meets all the requirements of this
series of checks is thereby determined to be satisfactory. An equipment that
fails in any one of several of the check requirements is assigned, by means of
proper references, to the appropriate steps in one or both of the two sections
described below.
c. ALIGNMENT -- This section details the steps necessary to
return the equipment to a properly aligned condition. Practical methods
requiring a minimum of maintenance time are employed.
d. TROUBLE ISOLATION --
This section of the procedure is divided into sections, each of which deals with
a specific component, stage or stages according to the function of the
equipment. When the maintenance technician is referred to a section of TROUBLE
ISOLATION by the failure of the equipment to meet the standards set up in
PERFORMANCE, he will find detailed instructions and data pertinent to the
function. Additional aids in the form of sectional schematics and suggested
testing techniques are at his fingertips. This eliminates time-consuming manual
searching, thus increasing the work output and efficiency of the
technician.
1--4.
DESCRIPTION OF PROCEDURE.
1--5. The
procedure begins with a general description of the appearance, function, and
operational characteristics of the AN/ARC-5 Communications Equipment. It is
followed by a block diagram, list of test equipment and tools, and other
necessary information. The procedure proper consists of PERFORMANCE CHECKS,
ALIGNMENT, and TROUBLE ISOLATION sections, each of these making use of pictorial
diagrams, photographs, and sectional schematics. These aids are related to the
written material by means of three types of symbols:
a. A star-encircled letter indicates a
MAJOR CHECK POINT, at which satisfactory PERFORMANCE can be most easily
determined.
b. An encircled numeral indicates SECONDARY CHECK POINT, at which
more detailed circuit information such as voltage readings and waveforms, can be
obtained for trouble analysis.
c. C-49 -- Manufacturer's circuit symbols,
used to cross-reference all diagrams with the written
material.
1--6. USE OF THE
PROCEDURE.
1--7. The proper procedure
to follow in bench maintenance work is that given by the sequence of the
PERFORMANCE CHECKS. These checks follow an order which will most quickly reveal
the proper or improper performance of the equipment.
1--8. The failure of the equipment to meet
one of these checks suggests the need for ALIGNMENT, or TROUBLE ISOLATION, and
appropriate references are made.
1--9. When the reason for defective
operation is found and the defect has been corrected, the technician is directed
to return to the PERFORMANCE section, repeat the step at which defective
operation was first noted, and, if PERFORMANCE is satisfactory, to continue with
the remainder of the PERFORMANCE CHECKS.
1--10. Satisfactory completion of the last PERFORMANCE CHECK
completes the bench maintenance for the equipment.
1--11. GENERAL DESCRIPTION OF AN/ARC-5
EQUIPMENT.
1--12. The model AN/ARC-5
Aircraft Radio Communication Equipment (See figure 1--1.) is a multi-channel
radio transmitter and receiver for use on aircraft having a 22 to 30-volt d-c
power supply. The receivers cover a frequency range of 190 kc to 9.1 mc in five
independent units, each unit designed to be mounted interchangeably into the
receiver racks. Racks are available for either two, and/or three-unit
installations, the receivers operating singly or simultaneously, depending upon
requirements. Provisions have been made for either local or remote control, but
only remote controls are furnished with the equipment. The receiver mounting
racks will accommodate other rack types of equipment such as the AN/ARR-2
Receiver and AN/ARC-5 VHF Transmitter-Receiver. These units will not be covered
in this procedure. The weight of the equipment, less cables and mechanical
linkages, is 23.6 pounds for a two-receiver installation and 55.2 for a
three-receiver installation.
1--13. The receivers are designed for the reception of CW, MCW or VOICE
modulation. Manual gain control is employed in conjunction with high level
automatic gain control. The outputs of each receiver may be paralleled on one
line to a single headset, or divided for double headset reception by more than
one operator. A 600-ohm headset is to be used with this equipment. A single
antenna is used for all receivers and transmitters. The tuning dials are
calibrated directly in mc and their accuracy is better than 0.5 per cent. The
transmitters cover the frequency range of 2.1 to 9.1 mc in five independent
units. They are designed to be installed in pairs. The transmitter frequency
control dial is calibrated in megacycles with an accuracy of .03 per cent or
better. A crystal calibrator is used in conjunction with an electron resonance
indicator to spot-check the dial calibrations of each unit. The current drain
from the d-c power source is 8.8 amperes when transmitting with CW emission, and
is reduced to 2.5 amperes on "stand-by". The carrier power output varies between
eight watts with VOICE modulation to 25 watts with CW emission.

Figure 1-2. Receiver and Transmitter Block
Diagrams
1--14. TEST
EQUIPMENT.

DESCRIPTION

RECOMMENDED STANDARD

ALTERNATE

1.

Bench Test Set

AN/GRM-1

AN/ARC-5 TEST BENCH HARNESS Stock No. RI6-R-1047-25

2.

Frequency Meter

LM-13

LM Series

3.

RF Signal Generator

TS-413/U

LP-5

4.

Audio Signal Generator

TS-382A/U

HP-200C

5.

Output Meter

Weston 695

Daven OP-182

6.

Voltmeter

TS-352/U

Simpson 260

7.

VTVM

TS-375/U

RCP 662 or RCA Voltohmyst 165

8.

Oscilloscope

TS 239/UP

Dumont 241

9.

Tube Tester

Hickok 547

Hickok 545 or 540

1--15. One additional extension cable will be
required for the bench test setup to record modulation wave forms in TROUBLE
ISOLATION. It should be a two-conductor cable about six inches long attached to
terminals 10 and 17 of plug 6962 (the plug that fits into modulator receptacle
(J-77). The other end of the two wire extension cable is terminated in two
insulated phone-tip jacks, properly identified as terminals I0 and 17
respectively.

Note
If the AN/ARC-5/ARR-2A Test Bench Harness, ASO stock
No. R16-R-1047-25, is used in place of the AN/GRM-1, there will be an individual
meter for each of the switch positions of the I-104-A and the TS-58/GRM-1. The
chart below shows the corresponding meter for each of the switch positions on
the I-104-A and the TS-58/GRM-1.

Figure 1-3. Test Equipment Diagram

I-104-A SWITCH POSITION

TEST UNIT #7369 METERS LABELLED

CIRCUIT

I-104-A READING

#7369 READING

1

INPUT VOLTAGE

Input voltage from primary source.

56

28 V DC

2

INPUT CURRENT

Total input current from the primary source.

14-17

1.4-1.7 A

3

PLATE VOLTAGE

Plate supply to 12SF7, 12SK7, and 12K8 tubes, and screen grid voltage
on 12A6 tube.

46-50

230-250 V

4

SCREEN VOLTAGE

Screen grid voltage to 12SF7, 12SK7 and 12K8 tubes.

38-50

76-100 V

5

CATHODE CURRENT

Cathode current of R-F amplifier and 1st I-F amplifier tubes, type
12SK7s.

44-60

11-15 ma

6

None

Basic movement of meter (50 micro-amperes) direct to-and-TEST METER
binding posts on front panel of I-104-A. I-104-A. Insert jumper wire
between these two posts to protect the meter
movement.

TS-58/GRM-1 SWITCH POSITION

TEST UNIT #9556 METERS LABELLED

CIRCUIT

TS-58/GRM-1 READING

#9556 READING

TONE

CW

TONE

CW

1

INPUT VOLTAGE

Input voltage from primary source

54

54

27

27

2

SCREEN VOLTAGE

Screen grid voltage to PA tubes

28-31

48-60

140-155

240-300

3

PLATE VOLTAGE

Plate voltage to final PA tubes

51-56

51-55

510-550

510-550

4

OSC. PLATE CURRENT

Plate current of master oscillator tube, type 1626

32-46

32-46

16-23

16-23 ma

5

AMP. PLATE CURRENT

Plate current of final PA tubes type 1625

27-40

60-80

68-100

150-200 ma

TEST SET COMPONENTS

QTY

DESIGNATION

TYPE

USE

ARMY

NAVY

1

Antenna

A-61-A

Phantom antenna (LF, MF, HF radio transmitter)

1

ANT. Relay Unit

BC-442-A

RE-2/ARC-5

Antenna relay (LF, MF, HF radio transmitter)

1

Control Unit

C-29/ARC-5

Transmitter control (or C-30A/ARC-5)

1

" "

C-43/ARC-5

Receiver control

3

" "

MC-237

Local tuning crank

1

Cord

CD-525

DC Outlet to modulator

2

"

CD-527

6-Conductor

1

"

CD-528

5-Conductor

2

"

CD-531

DC Outlet to receiver rack (2-Conductor)

2

"

CD-532

8-conductor

1

"

CD-706

Receiver Rack adapter (7-Conductor)

1

"

CD-905

Sidetone test

2

"

CX-31/GRM-1

12-Conductor

1

"

CX-32/GRM-1

18-Conductor

1

"

CX-33/GRM-1

Transmitter rack adapter (7-Conductor)

6

Diagram

Instructions for test equipment AN/GRM-1

1

Dynamotor

DM-33-A

DY-8/ARC-5

Dynamotor (transmitting)

1

Modulator

MD-7/ARC-5

Modulator equipped with tubes

1

Mounting Base

FT-279-A

MT-62/ARC-5

Mounting for MT-63/ARC-5 or FT-277-A Receiver rack

1

"

FT-227-A

MT-70/ARC-5

Mounting for MT-71/ARC-5 Radio transmitter rack

1

"

FT-225-A

MT-76/ARC-5

Mounting (modulator)

1

"

FT-229-A

MT-77/ARC-5

Mounting (antenna relay unit)

1

Mounting Plate

FT-228-A

MT-80/ARC-5

Mounting (transmitter control C-29/ARC-5 or
C-50A/ARC-5)

1

"

FT-222-A

MT-98/ARC-5

Mounting (Receiver control C-43/ARC-5)

1

Mounting Rack

FT-277-A

MT-63/ARC-5

Rack for two radio receivers

1

"

MT-71/ARC-5

Rack for two radio transmitters

1

Test Unit

I-104-A

Test unit for radio receivers

1

"

TS-58/GRM-1

Test unit for radio transmitters

1

Cord

CD-307-A

Headset extension cord

1

Microphone

RS-38A

Microphone

1

Headset

HS-33

600-ohm headset (two ANB-H-1 receivers or
equivalent)

Figure 1-4. Cable Assemblies CD 532 and CD 528

Figure 1-5. Cable Assemblies CD 531 and CD 525

Figure 1-64. Cable Assemblies CX-31/GRM-1 and
CS-32/GRM-1

Figure 1-74. Cable Assembly CD
527
NOTES1. If Antenna relay unit RE-2/ARC-5, being
tested, does not have a series capacitor, connect the transmitter to "TRANS".
Connect "ANT" of the antenna relay unit to terminal "A", instead of to terminal
"5", of antenna A-61-A.
2. Test Unit I-104-A normally is used with adapter
cord CD-706 as shown. It may be used by attaching cord CD-532 to either position
of the receiver rack and when so employed, the meter will not indicate when the
meter switch is in position four or five. Volume control on AVC directly affects
sidetone level.
3. The drawing shows the mechanical linkage (Part No. 6151)
so that the mechanical tuning features of the control units C-26 and C-43/ARC-5
and radio receivers R-20 to R-27/ARC-5 may be tested. No linkage is furnished
with the test equipment. Control unit MC-257 (local tuning crank) is furnished
for testing these receivers.

4. Test unit I-104-A may be made to function
as a control unit and provide the channel selection when testing VHF radio
receiver R-28/ARC-5, by connecting cord CD-527 between jack J-103 on the radio
receiver and jack J-600 on the test unit.
5. Dynamotors *DY-2/ARR-2 and
*DY-2A/ARR-2 are furnished with the particular radio receivers as shown. Both
dynamotors are interchangeable with dynamotors DM-32-A or CBY-21531.

6.
Transmitters and receivers may be tested either by direct connection to the test
equipment, using cords CX-33/GRM-1 and CD-706, or by mounting in a one or two
unit rack and using cords CX-31/GRM-1 and CD-532.
SECTION II PERFORMANCE CHECKS
2--1. GENERAL.
2--2. These PERFORMANCE CHECKS are to be made in the order
given; when a performance requirement is not met, a reference is made to the
appropriate voltage measurement or signal tracing procedure in TROUBLE
ISOLATION. ALIGNMENT PROCEDURES are included, but are to be used only as
directed in TROUBLE ISOLATION. Signal tracing techniques are used after voltage
readings have been found to be normal. The standard maintenance manual should be
referred to for detailed information concerning the AN/ARC-5
Equipment.

Note
Receiver and transmitter PERFORMANCE CHECKS are
divided as shown in the TABLE OF CONTENTS.
2--3. VISUAL CHECKS.
Connect the unit to be checked on the Test Set AN/GRM-1 rack and inspect the
unit for the following:
l. Faulty plugs, threads and pins.
2. Improper
fusing.
3. Note evidence of excessive dynamotor ripple at the headset while
tuning through the frequency band.
4. Dirty and chattering antenna relay
contacts.
5. Excessive vibration of the unit in rack.

Note
Open filaments can sometimes be detected by noting
cold tubes.
2--4. RECEIVER CHECKS.
2--5. D-C POWER SUPPLY AND OPERATING VOLTAGES.
2--6. LIMITS: Input
voltage is 27.5 volts dc at 1.7 amps.
Secondary voltage is 230-250 volts dc
at 60 ma.
2--7. PRELIMINARY INSTRUCTIONS: Use Test Set AN/GRM-1, as shown in
figure 1-3. Use "Optional Wiring" for greater ease in maintenance testing. Do
not key the transmitter. Apply d-c power and turn the CONTROL SWITCH of Test Set
I-104-A to MCW position, allowing the equipment time to warm up. Do not remove
the cover plates until trouble isolation or alignment is indicated by
performance failure. Advance INCREASE OUTPUT control to full clockwise
position.

Figure 2-1. Modulation Envelopes

2--8. TEST PROCEDURE.

STEP

HEAD TEST SET

METER SW

CIRCUIT MEASURED

NORMAL VALUES

NORMAL METER INDIC.

ABNORMAL METER INDIC.

1

I-I04-A

1

Input voltage

27.5 v

56

Refer to TROUBLE ISOLATION PROCEDURE, Section IV, Paragraph
4-1.

2

I-I04-A

2

Input current

1.4-1.7 a

14-17

3

I-I04-A

3

Plate supply

230-250 v

46-50

4

I-I04-A

4

Screen supply

76-100 v

38-50

5

I-I04-A

5

Cathode current RF and 1st IF tubes

11-15 ma

44-60

2--9. BAND NOISE.
2--10. LIMITS: (Less than 15 milliwatts.)
2--11. TEST
PROCEDURE.

STEP

TEST SET I-1O4-A

NORMAL OUTPUT INDICATION AND CONNECTIONS

POSSIBLE CAUSES OF ABNORMAL IND.

1

CONTROL SWITCH to CW or MCW. INCREASE OUTPUT control to maximum.
Connect dummy antenna (100 mmfd capacitor) from Antenna post to ground.
Use short leads.

Output Meter, OP-182, and headphones connected to headset jack of
1-104-A. Switch set to 600 ohms.

2

Peak receiver ALIGN INPUT trimmer for maximum output at the high
frequency end of dial.

Reads less than 1.5 mw of noise.

Check dynamotor brushes and bearings. Replace dynamotor, if
necessary.

3

Turn the receiver frequency dial from high to the low end and note the
maximum noise in the output meter.

Never exceed 1.5 mw.

Same.

2--12. SENSITIVITY.
2--13. LIMITS. Less than 10 uv R-F input to obtain 10 mw audio output
with INCREASE OUTPUT control set at maximum.
2--14. TEST PROCEDURE.

STEP

RECEIVER SETTINGS

SIG. GEN CONNECTIONS

OUTPUT INDIC. & CONNECTIONS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL IND.

1

FREQUENCY at high end; MCW operation: INCREASE OUTPUT control at
maximum.

Through .006 mfd capacitor, to receiver Antenna post. Set frequency to
agree with receiver.

Output meter, OP-182, and headphones connected to headphone jack. Set
switch to 600 ohms.

Peak ALIGN INPUT trimmer.

Use modulated RF 30 per cent at 400 or 1000 cycles.

Maximum output.

A peak on output meter.

2

Same as Step 1.

Vary attenuator to obtain 10 mw receiver output.

Same as Step 1.

10 uv input, or less, to obtain 10 mw audio output.

Refer to TROUBLE ISOLATION, Section IV, paragraphs 4--4 to 4--11, and
ALIGNMENT PROCEDURE, Section 3--1.

3

Same as Step 1. except switch to CW. Rock receiver dial carefully for
maximum output.

Turn MODULATION switch to OFF. Vary attenuator to obtain 10 mw receiver
output.

Same as Step 1.

3.5 uv input to obtain 10 mw output.

Check CW oscillator and ALIGNMENT PROCEDURE, Section III, paragraph
3--1.

4

Repeat Steps 1 through 3 with receiver dial set at low
end.

2--15. SELECTIVITY.
2--16. PRELIMINARY ADJUSTMENTS: Set the Model 695 output meter to the 1.5
volt range. Connect a 300-ohm one-half or one watt composition resistor in
parallel with the output meter; connect output meter to receiver phone jack. Set
the receiver INCREASE OUTPUT control to full counterclockwise position. Tune the
receiver and the signal generator to the proper frequency, as given in Table
below. Adjust the signal generator attenuators for 50 microvolts output, 30 per
cent modulated at 400 cycles. Advance the INCREASE OUTPUT control clockwise
until the Model 695 output meter reads 1.0 volts. The receiver dial and the
ALIGN INPUT trimmer should be adjusted for maximum output meter reading.
Readjust the INCREASE OUTPUT control as necessary to give output meter reading
of 1.0 volts. Receiver should be set for MCW operation.

STEP

OUTPUT METER SETTINGS

SIGNAL GENERATOR SETTINGS

1

Switch output meter to 15 volt range.

Adjust the output attenuators for 500 microvolts output. (Switch
MULTIPLIER to 100 position.) Slowly detune FREQUENCY dial higher in
frequency until output meter reads less than 6.O volts.

2

Switch output meter to 6 volt range.

Slowly detune FREQUENCY dial higher in frequency until output meter
reads slightly less than 1.5 volts.

3

Switch output meter to 1.5 volt range.

Slowly and carefully detune FREQUENCY dial higher in frequency until
output meter reads 1.0 volts.

4

Record the amount of frequency deviation from original setting at
resonance, as given in PRELIMINARY ADJUSTMENTS.

5

Repeat Steps 1 through 4.

Repeat Steps 1 through 4, detuning the FREQUENCY dial lower in
frequency.

6

Compare values obtained in Steps 4 and 5; they should be very nearly
equal in value. Amount of frequency deviation recorded in Steps 4 and
should not exceed values given in Table below by more than 10 per
cent.

7

Repeat Steps I through 5 on the R-23 (.19-.55 mcs.) receiver, with
50,000 microvolts input, instead of 500. Specifications given in Step 6
also apply.

RECEIVER

FREQUENCY

FREQUENCY DEVIATION EITHER SIDE OF RESONANCE

R-23 .19-.55 mcs.

.19 mcs.

3.0 kcs. 6.0 kcs.***

R-24 .52-1.5 mcs.

.52 mcs.

5.0 kcs.

R-25 1.5-3.0 mcs.

1.5 mcs.

7.0 kcs.

R-26 3.0-6.0 mcs.

3.0 mcs.

15.0 kcs.

R-27 6.0-9.0 mcs.

6.0 mcs.

28.0 kcs.

*** at 50,000 microvolts input
2--17. AVC
CHARACTERISTICS.
2--18. LIMITS:
10X
Normal sensitivity -- 50 to 150 mw.
100X Normal sensitivity -- 100 to 200
mw.
1000X Normal sensitivity -- 200 mw.
10000X Normal sensitivity -- 200
to 400 mw.

Note
Normal sensitivity is that setting of the signal
generator output necessary to produce 10 mw receiver output.
2--19. PRELIMINARY
INSTRUCTIONS. Obtain normal sensitivity before starting this check. This check
may be omitted on R-23 and R-24 navigation receivers.
2--20. TEST
PROCEDURE.

STEP

SIGNAL GENERATOR CONNECTIONS

OUTPUT INDIC. & CONNECTIONS

NORMAL INDIC.

POSSIBLE CAUSES OF ABNORMAL INDICATION

1

Same as Steps 1 and 2 of SENSITIVITY check.

1. Audio amplification is insufficient. Refer to TROUBLE ISOLATION,
Section IV, paragraph 4--4.

2

Increase attenuator setting 1000X the setting at normal
sensitivity.

Record reading of output meter.

200 mw indicates that the audio level is sufficient for normal
operation.

2. Faulty AVC indicated by a decreasing output with increased signal
input.

3

Increase attenuator setting 10000X the setting at normal
sensitivity.

Same as Step 1.

200 to 400 mw

Refer to TROUBLE ISOLATION, Section IV, paragraph
4--7.

4

Set attenuator to 100X the setting at normal sensitivity.

Same as Step 1.

100 to 200 mw

5

Set attenuator to 10X the setting at normal sensitivity.

Same as Step 1.

50 to 150 mw

2--21. TRANSMITTER
CHECKS.
2--22. POWER SUPPLY.
2--23.
LIMITS: Input voltage 27.5 v dc.
Secondary voltage 545 v dc.
2--24.
PRELIMINARY INSTRUCTIONS: Use Test Set, AN/GRM-1, as shown in figure 1--3. Apply
d-c power and allow time for the equipment to warm up. Depress the test key when
recording all tests.
2--25. TEST PROCEDURE.

STEP

C-29/ARC-5 CONTROL BOX

OPERATION

TS-58/GRM-1 READS

VOLTMETER VALUES

POSSIBLE CAUSES OF ABNORMAL IND.

1

Select transmitter 1 or 2 corresponding to the rack position of unit.
Switch to CW and key transmitter.

Dynamotor runs. Note any evidence of overload in the form of excessive
noise or heat.

Refer to TROUBLE ISOLATION, Section IV, paragraph
4--12.

2

Same.

Switch TS-58 to Position 1; read heater voltage.

54 divisions.

27.5 v

3

Same.

Switch TS-58 to Position 3; read B+.

51-55 divisions.

510-550 v

4

Switch to VOICE or TONE. Key transmitter.

Same.

51-55 divisions.

510-550 v

2--26. TRANSMITTER TRACKING AND
LOADING.
2--27. LIMIT: Phantom Antenna
Plate Current:

TS-58/GRM-1, pos. 5 Current

No load (zero coupling)

10

25 ma

Loaded-MCW-VOICE

20-40

50-100 ma

Loaded-CW

60-80

150-200 ma

Frequency Calibration:
Within 0.03% of dial reading at any frequency,
except at crystal frequency, where tolerance b 0.05%. ****
R-F Power
Output:CW emission--2.25 amps minimum (25 watts)
VOICE emission--l.61 amps
minimum (13 watts) unmod.
TONE emission--1.85 amps minimum (17 watts)
****
Above -- listed values of current measured on the ARC No. 7777 Phantom Antenna
R-F current meter.
2--28. TEST PROCEDURE.

STEP

TRANSMITTER CONTROLS

OPERATION

NORMAL INDICATION

ABNORMAL INDICATION

1

Select and switch on transmitter 1 or 2 depending on position in rack.
Switch to CW. Unlock all transmitter controls. Set COUPLING and ANT.
INDUCTANCE at zero.

Set TS-58/GRM-I switch to position 5. Set transmitter dial to the
lowest frequency. Observe TS-58 GRM-1 meter while tuning transmitter dial
throughout its range.

TS-58/GRM-1 meter reading should not exceed 10 through out the range of
the tranmitter FREQUENCY dial.

Refer to TRANSMITTER ALIGNMENT, Section III, paragraph 3t6. Refer to
TROUBLE ISOLATION, Section IV, paragraph 4---16.

2

Set FREQUENCY dial, 100 kc from high end.

3

Set COUPLING at 3, and key the transmitter.

Vary ANT INDUCTANCE from 0 upward, until antenna current is indicated.
Adjust COUPLING and ANT INDUCTANCE carefully for maximum antenna current.

Antenna meter reads 2.0 to 3.0 amps. TS-58/GRM-1, position 5, reads
60.80 (150-200 ma).

Refer to TROUBLE ISOLATION, Section IV, paragraphs 4--15 and
4--16.

4

Switch to VOICE. Key transmitter,

Reduce COUPLING to zero; then advance clockwise until antenna meter
reads 1.6 amps.

Antenna meter reads 1.6 amps. TS-58/GRM-1, position 5, reads 20-40
(50-100 ma).

Refer to TROUBLE ISOLATION, Section IV, paragraphs 4--16 and
4--17.

5

Same. Key transmitter,

Loosely couple LM frequency meter to transmitter and adjust it for
zero-beat with transmitter frequency.

Frequency as indicated by the LM should be within .03 per cent of the
frequency indicated on transmitter dial.

Refer to TRANSMITTER ALIGNMENT, Section III, paragraph
3----6.

6

Repeat Steps 3, 4, and 5 with transmitter dial set at 100 kc from low
end of band.

7

Repeat Steps 3, 4, and 5 with transmitter dial set to the crystal
frequency.

8

Repeat Steps 3, 4, and 5 with transmitter dial set to the operating
trequency.

9

Lock all controls except coupling
control.

2--29. MODULATION CHECK.
2--30. PRELIMINARY INSTRUCTIONS:
Modulation capabilities of the
transmitter are determined by use of the oscilloscope, displaying a modulation
envelope type of pattern. In addition to the normal oscilloscope control
settings, the following should be observed:
Oscilloscope Settings--Vertical
input to plates direct. Sync control to EXTERNAL.
Oscilloscope
Connections-Sync voltage is obtained from one of the phone jacks in receiver
rack or junction box. The vertical input terminal of the oscilloscope is loosely
coupled to the transmitter R-F output, by attaching a wire, having good R-F
insulation, to the vertical input terminal. The other end of this wire is
brought close to the phantom antenna lead from the transmitter. The degree of
coupling between these two leads will determine the vertical height of the
modulation pattern.

STEP

TRANSMITTER CONTROLS

OPERATION

NORMAL INDICATION

ABNORMAL INDICATION

1

Set emission to TONE. Key transmitter. Adjust COUPLING control for
maximum Antenna current.

Adjust sweep frequency controls of scope until two or more audio cycles
are displayed. Adjust Sync control for steady pattern.

Sinewave envelope pattern with no appreciable distortion; see figure
2--1. Modulation percentage should be 60 per cent or better as calculated
by use of formula below.

Refer to TROUBLE ISOLATION, Section IV, paragraph
4--17.

2

Set emission to VOICE. Key transmitter.

Speak in mike at normal voice level.

Observe that the modulation peaks rise to a higher value than that
obtained for normal indication in Step 1.

Refer to TROUBLE ISOLATION, Section IV, paragraph
4--17.

MODULATION
FORMULA: (A-B)/(A+B) * 100 = % modulation

SUMMARY TEST DATA CHECK OFF SHEET

AN/ARC-5

Antenna Relay__________Mike Jack___________Phone
Jack___________Dynamotor Ripple ___________
Calibration
(.08%)__________Vibration____________Align Input__________Dyn. Overhaul
Date_________
Max. Band Noise .19-.55mc .52-1.5mc 1.5-3.0mc 3.0-6.0mc
6.0-9.1mc
(15 mw) ________ ________ ________ ________ _________SENSITIVITY
HIGH END LOW END AVC CHARACTERISTICS
(7uv) CW MCW INPUT OUTPUT
RATIO
LIMITS
.19-.55mc _________________ _________________ NOR. SENS. ________ uv.
(mw)
.52-1.5mc _________________ _________________ 5X ________
50-1001.5-3.0mc _________________ _________________ 10X ________
50-150
3.0-6.0mc _________________ _________________ 100X ________
100-200
6.0-9.1mc _________________ _________________ 1000X ________
100-300
10000X ________ 200-400 AUDIO OUTPUT CW ________ MCW ________ 200
200
SELECTIVITY
RECEIVER .19-.55mc .52-1.5mc 1.5-3.0mc 3.0-6.0mc 6.0-9.1mc
LIMITS
2X ________ ________ ________ ________ _________ 2X -- 2.1-10
kc

10X ________ ________ ________ ________ _________ 10X -- 5-10
kc
10000X ________ ________ _________ ________ _________ 10000X -- 18
kc
TRANSMITTER POWER TRANSMITTER TRANSMITTER TRANSMITTER
OUTPUT FREQUENCY
MODULATION TUNE-UP
CW __________
26 to 40 CW _________ VOICE _________
VOICE _________
.05% Approx. 70% Max. ant.
current
TONE
__________
13 to 26
VOICE __________ CHANNEL SEL. POWER SUPPLY
13 to 26
1 ______ 2 ______ IN _______ OUT ______
27.5Vdc 545Vdc
SECTION III ALIGNMENT PROCEDURE
3--1. RECEIVER
ALIGNMENT.

Figure 3-1. Receiver Alignment Connections

Figure 3-2. Location of Trimmers, Typical
Receiver
3--2. PRELIMINARY INSTRUCTIONS.Output Meter--Daven, Model
OP-182, connected into headset jack on receiver rack; IMPEDANCE SELECTOR set at
300 ohms.
Signal Generator--LP-5 or Hickok 19X connected between the point
indicated on alignment chart and ground.
Controls-Set gain control at
maximum, emission to MCW, signal generator switch ON, and dial as indicated in
chart.
Output Level--During alignment, the signal generator output must be
attenuated to maintain the receiver output at 10 mw as indicated by output
meter.3--3. RECEIVER ALIGNMENT NOTES.3--4. The receivers R-23, R-24 and R-23A
normally operate with over-coupled I.F stages. For alignment, each I-F stage
must be loosely coupled by pulling out the bakelite rod to the snap-out
position. After the entire alignment is completed, the I-F stage must be
returned to the same over-coupled condition. For the R-23 and R-24, over-couple
the first I-F stage; for the R-23A and R-148, over-couple all I-F
stages.
3--5. RECEIVER ALIGNMENT PROCEDURE. (See figures 3--1 and 3--2.)
Before beginning alignment, check the positions of C4F and C4G and adjust them
if necessary
to the position shown in the table which follows. The positions
shown are as seen from the FRONT of the receiver.

RECEIVER

C4F

C4G

R-23

R-24

R-25

R-26

R-27

Front of Receiver

STEP

SIGNAL GENERATOR

RECEIVER

SPECIAL INSTRUCTIONS

TRIMMERS

CONNECTIONS TO RECEIVER

FREQUENCY SETTINGS

TYPE

DIAL SETTING

1

Through .006 mfd capacitor to mixer grid use MOD RF.

85 kc

239 kc

705 kc

1415 kc

2830 kc

R-23 R-24 R-25 R-26 R-27

ANY DIAL SETTING

See Receiver Alignment Note, paragraph 3--3. Adjust all I-F trimmers as
indicated at right, for maximum output meter reading.

C-21

C-38

C-37

C-18

C-36

C-13

2

Same Use PURE RF.

Same

Switch receiver to CW and adjust BFO trimmer for
zero-beat.

C-28

3

Same Use MOD RF.

.52 mc

1.4 mc

2.9 mc

5.8 mc

8.9 mc

R-23 R-24 R-25 R-26 R-27

.52 mc

1.4 mc

2.9 mc

5.8 mc

8.9 mc

Switch to MCW. Adjust oscillator trimmer for maximum output meter
reading.

C-4E

4

Through .006 mfd capacitor to ANT post.

Same

Same

Adjust R-F trimmer and ALIGN INPUT trimmer for maximum output.

C-4D

C-2

5

Same

Same

Same

Adjust oscillator trimmer for maximum output.

C-4E

6

Same

.21 mc

.57 mc

1.55 mc

3.1 mc

6.1 mc

R-23 R-24 R-25 R-26 R-27

.21 mc

.57 mc

1.55 mc

3.1 mc

6.1 mc

Adjust oscillator padder, while carefully rocking the receiver dial,
for maximum output.

C-9

7

Repeat Steps 5 and 6 two or more times until there is no further
increase in output when Step 5 is performed. Then, proceed with Step
8.

8

Same Use PURE RF.

Same as Step 5

Same as Step 5

Switch to CW. Adjust oscillator trimmer for zero-beat.

C-4E

9

Return I-F transformers to overcoupled condition: See Receiver
Alignment Note, paragraph 3--3.

Figure 3-3. Transmitter Alignment Connections)

Figure 3-4. Transmitter Adjustment Points (Top)

Figure 3-5. Transmitter Adjustment Points
(Bottom)
3--6. TRANSMITTER
ALIGNMENT.
3--7. PRELIMINARY
INSTRUCTIONS.
Bench Setup- Connect transmitter, with outer shield removed, to
AN/GRM-1, as shown in figure 1--3.
Frequency Meter -- LM-13 -- Couple as
indicated in Transmitter Alignment Chart, (See figure 3--3.).3--8. TRANSMITTER
ALIGNMENT NOTES.3--9. Zero-beat should occur at mid-position of E-62. If it is
impossible to obtain a zero-beat with E-62, C-60 may be unlocked from its normal
locked position and adjusted to give a zero-beat with E-62 at mid-position.3-10.
To correct frequency error at the low end, transmitter FREQUENCY by
over-shooting the correct setting an amount one-half that of the error. Adjust
E-58 for zero-beat. Reset FREQUENCY to correct setting and retrim C-60 for
zero-beat. The reason for the latter operation is to achieve accuracy at the
high and low frequency points with a minimum number of steps.
3-11. To
correct the tracking error, E-59 should be adjusted at the low frequency and by
over-shooting by one-half the number of turns necessary to obtain minimum plate
current.TRANSMITTER ALIGNMENT CHART (See figures 3--4 and 3--5.)

STEP

CONNECTIONS ON TS-58/GRM-1

DIAL SETTING

TRANSMITTER OPERATION

ADJUST

1

Connect Phantom Antenna to transmitter antenna post.

Turn transmitter ON. Key transmitter. Check FREQUENCY against crystal
frequency by tuning for greatest shadow on resonance
indicator.

FREQUENCY knob

2

T-18 2.9 mc

T-19 3.9 mc

T-20 5.2 mc

T-21 6.9 mc

T-22 9.0 mc

Turn FREQUENCY dial to setting indicated; Emission switch to VOICE. Key
transmitter. Load transmitter by adjusting for maximum antenna
current.

ANT IND.

ANT COUP.

3

Frequency meter loosely coupled to dummy load and set to same
frequency.

Same as Step 2.

Adjust master oscillator trimmer for zero-beat in frequency meter
headphones. (See Transmitter Alignment Notes, paragraph
3--9.)

E-62

4

Same as Step 3.

T-18 2.2 mc

T-19 3.1 mc

T-20 4.1 mc

T-21 5.4 mc

T-22 7.1 mc

Turn FREQUENCY dial to setting indicated. Vary FREQUENCY dial for
zero-beat and note error. To correct, adjust master oscillator inductance.
(See Transmitter Alignment Notes, paragraph 3--10.)

E-58

5

Repeat Steps 3 and 4 until the final setting of E-62 with to cover in
place is at a mid-position and dial setting at the high and low is
accurate. Dial setting should be within 0.03 per cent of actual frequency
as indicated by LM frequency meter.

6

Remove Phantom Antenna to align R-F amplifier. Remove frequency meter
and coupling. TS-58/GRM-I switch to position 5.

Same as Step 2.

Adjust for minimum R-F amplifier plate current, which should be below
10 divisions (25 ma) on TS-58/GRM-1 meter.

C-67 (normally locked)

7

Same as Step 4.

Turn FREQUENCY dial to setting indicated to check tracking; note if the
minimum R-F plate current is within 10 ma of the minimum obtained in Step
6. To correct, adjust iron core. (See Transmitter Alignment Notes,
paragraph 3--1 l.)

8

Repeat Steps 6 and 7 until R-F amplifier is operating at minimum plate
current at the high frequency end and until tracking error is
corrected.

9

Reconnect Phantom Antenna to transmitter antenna post.

Adjust transmitter for maximum antenna current output. Lock all dial
controls at completion of this check.

ANT IND.

ANT COUP.

SECTION IV TROUBLE
ISOLATION

Figure 4-1. Typical Communications Receiver, Bottom
View

Figure 4-2. Typical Receiver, Top View Inside, and Bottom View
Dynamotor
4--1. RADIO
RECEIVER.
4--2. DYNAMOTOR UNIT.4--3.
PRELIMINARY INSTRUCTIONS: All tests on the receiver will be performed using the
AN/GRM-1 Test Setup, as shown in figure 1--3.

STEP

TEST POINT

TEST EQUIPMENT CONTROLS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL INDICATION

1.

A

Control switch to MCW or CW position. Meter switch to
position 3.

Dynamotor scans; I-104-A meter indicates from 46 to 50
(230 to 250 volts dc):

Shorted or open dynamotor windings; defective plugs or jacks; open
choke L-14, L-15.

2.

B

Control switch to MCW or CW position. Meter switch to position 1 and
2.

Position 1; meter reads 56 (28 volts dc). Position 2; meter reads 14 to
17 (1.4-1.7 amps).

Blown fuses; defective plugs or jacks; open wiring, shorted or open
dynamotor windings.

4--4. AUDIO-FREQUENCY CIRCUIT.
(See chart below.)
4--5. PRELIMINARY INSTRUCTIONS: Set
Audio Signal Generator to 1000 cycles, zero output. Connect TS-375/U or TS-352/U
a-c test leads across Audio Signal Generator output terminals. Connect the other
pair of test leads from Audio Signal Generator output terminals to indicated
test points and chassis.

STEP

TEST

POINT

TEST EQUIPMENT

CONTROLS

ARC-5 RECEIVER

CONTROLS

NORMAL

INDICATION

POSSIBLE CAUSES OF

ABNORMAL INDICATION

1

C

Set voltmeter on 3 (or 2.5) volt a-c range. Advance the output level
control on Audio Signal Generator for 2.25 volt reading on
voltmeter.

Control switch to MCW position.

Output meter reading of 200 miIliwatts or greater.

If normal, proceed to paragraph 4--6. If not, proceed with Step 2,
paragraph 4--5.

2

D

Same as Step 1.

Same as Step 1.

Same as Step 1.

Faulty power amplifier tube and/or circuit components, Repair and
return to Step 1, paragraph 4--5 before going to paragraph 4--6.

Figure 4-3. Dynamotor Test Points

Figure 4-4. Audio Frequency Test Points
4--6. INTERMEDIATE-FREQUENCY
CIRCUIT.
(Follow chart below.)4--7.
PRELIMINARY INSTRUCTIONS: Insert a 0.006 ufd capacitor in series with the "hot"
lead from the Signal Generator to the receiver. Use a signal modulated 30 per
cent at 400 or 1000 cycles. Connect Signal Generator to indicated TEST
POINT.

STEP

TEST

POINT

TEST EQUIPMENT

CONTROLS

ARC-5 RECEIVER

CONTROLS

NORMAL

INDICATION

POSSIBLE CAUSES OF

ABNORMAL INDICATION

1

D

Tune the Signal Generator to the following appropriate frequency. (Rock
the Signal Generator FREQUENCY dial for maximum output meter reading.)

Set the CONTROL switch on the I-104-A Test Unit to MCW
position.

Output of 10 milliwatts or greater across the 300-ohm load, for Signal
Generator input as follows:

If normal, proceed to Step 1,paragraph 4--8. If not, proceed to Step 2,
paragraph 4--7.

UNIT

FREQUENCY

.19-.55 mc

85 kc

310 uv

.52-1.5 mc

239 kc

360 uv

1.5-3.0 mc

705 kc

910 uv

3.0-6.0 mc

1415 kc

330 uv

6.0-9.1 mc

2830 kc

430 uv

2

1

Same as in Step 1.

Same as in Step 1.

Same output as in Step 1. Signal Generator input as
follows:

If normal, trouble it in converter stage. If not normal proceed to Step
3, paragraph 4--7.

8100 uv

7500 uv

10,000 uv

2400 uv

2500 uv

3

2

Same as in Step 1.

Same as in Step 1.

Same output as in Step 1. Signal Generator input as
follows:

If normal, trouble is in 1st I-F stage. If not normal, trouble is
probably in 2nd I-F stage.

210,000 uv

220,000 uv

130,000 uv

99,000 uv

85,000 uv

Note
When a stage is found defective, test the tube in a
tube checker and replace with good tube if necessary. Conduct routine resistance
and voltage measurements to locate the defective or faulty component or
components within a stage. When trouble has been located and corrected, return
to Step 1, paragraph 4--7 to determine that I-F stages are operating
satisfactorily.
4--8. CONVERTER CIRCUIT.(Follow chart below).
4--9. PRELIMINARY INSTRUCTIONS: Use a
signal 50 per cent modulated at 400 or 1000 cycles. Connect R-F Signal Generator
between the TEST POINT and chassis. When using the VTVM, the d-c probe having
several megohms of series isolating resistance inserted at its tip should be
used. (See figures 4--7 and 4--8.)

STEP

TEST

POINT

TEST EQUIPMENT

CONTROLS

ARC-5 RECEIVER

CONTROLS

NORMAL

INDICATION

POSSIBLE CAUSES OF

ABNORMAL INDICATION

1

1

Tune the Signal Generator to the following appropriate frequency. (Rock
the Signal Generator FREQUENCY dial for maximum output.)

Set the CONTROL switch on the I-104-A Test Unit to MCW
position.

Output of 10 milliwatts or greater across the 300-ohm load, for Signal
Generator input as follows:

Defective 12K8 tube; defective circuit components; improper alignment.
(Proceed to step 2 to check the oscillator circuit.) If normal, proceed to
step 1, paragraph - 4--10.

UNIT

FREQUENCY

FREQUENCY

NORMAL SENS.

.19-.55 mc

.55 mc

.55 mc

370 uv

.52-1.5 mc

1.5 mc

1.5 mc

430 uv

1.5-3.0 mc

3.0 mc

3.0 mc

990 uv

3.0-6.0 mc

6.0 mc

6.0 mc

390 uv

6.0-9.1 mc

9.1 mc

9.1 mc

480 uv

2

2

Set VTVM to 12-volt d-c range, negative polarity. Connect d-c probe to
TEST POINT.

Vary the frequency from the high end to the low end of the
dial.

VTVM indicates a -6 to -9 volts. This voltage varies over the frequency
range.

Weak or defective oscillator section of 12K8 converter tube. Defective
components. Improper alignment.

4--10. RADIO-FREQUENCY
CIRCUIT.
( Follow chart
below).

STEP

TEST

POINT

TEST EQUIPMENT

CONTROLS

ARC-5 RECEIVER

CONTROLS

NORMAL

INDICATION

POSSIBLE CAUSES OF

ABNORMAL INDICATION

1

1

Same as Step 1, paragraph 4--8.

Control to MCW

Loud clear tone.

R-F tube or circuit. If normal proceed to Step 1, paragraph
4--11.

UNIT

FREQUENCY

FREQUENCY

NORMAL SENS.

.19-.55 mc

.55 mc

.55 mc

50 uv

.52-1.5 mc

1.5 mc

1.5 mc

80 uv

1.5-3.0 mc

3.0 mc

3.0 mc

150 uv

3.0-6.0 mc

6.0 mc

6.0 mc

130 uv

6.0-9.1 mc

9.1 mc

9.1 mc

100 uv

4--11. ANTENNA CIRCUIT.
(Follow chart below).

STEP

TEST POINT

TEST EQUIPMENT CONTROLS

ARC-5 RECEIVER CONTROLS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL INDICATION

1.

E

Same as Step 1, paragraph 4--8

Control to MCW

Loud clear tone in headset.

Antenna circuit. If normal, this completes the receiver
check.

UNIT

FREQUENCY

FREQUENCY

NORMAL SENS.

.19-.55 mc

.55 mc

.55 mc

5 uv

.52-1.5 mc

1.5 mc

1.5 mc

7 uv

1.5-3.0 mc

3.0 mc

3.0 mc

7 uv

3.0-6.0 mc

6.0 mc

6.0 mc

6 uv

6.0-9.1 mc

9.1 mc

9.1 mc

6 uv

Figure 4-5. Circuit Test Point Diagram
4--12. TRANSMITTER AND
MODULATOR.
4--13. DYNAMOTOR
UNIT.
4--14. PRELIMINARY INSTRUCTIONS: All tests on the transmitter will be
performed using the AN/GRM-1 Test Setup optional wiring, illustrated in Figure
1--3, or the AN/ARC-5 Test Bench Harness. Select transmitter one or two,
corresponding to the desired unit's position in the test rack. (See figure
4--15.)

STEP

TEST POINT

TEST EQUIPMENT CONTROLS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL INDICATION

1.

F

Emission selector switch to CW. TRANS. POWER switch to ON. Switch on
TS-58 set to position 1.

Filaments light; relays K-5O, K-53, and K-54 energized; dynamotor runs.
TS-58 meter indicates 54 (27 volts).

Fuses F-50 and F-5I blown; defective coils on relays; dirty or corroded
contacts; defective dynamotor.

2.

G

Switch on TS-58 set to position 3. Key the transmitter.

TS-58 meter reads 51-55 (510-550 volts d-c.)

Defective relay K-52; defective dynamotor windings; shorted C-55;
shorted components in 550-volt circuit; defective plugs and jacks on
equipment.

Figure 4-6. Circuit Test Points

Figure 4-7. Converter Circuit Test Points

Figure 4-8. Converter Circuit Test Points

Figure 4-9. Antenna Circuit Test Diagram

Figure 4-10. Antenna Circuit Test Points

Figure 4-11. Typical Transmitter, Top View, Shield
Removed
4--15.
OSCILLATOR.
(Follow chart
below.)

STEP

TEST

POINT

TEST EQUIPMENT

CONTROLS

NORMAL

INDICATION

POSSIBLE CAUSES OF

ABNORMAL INDICATION

1.

Emission selector switch to CW. Set VTVM on 120-volt d-c scale,
--polarity and connect to TEST

POINT H, the ungrounded terminal of PA grid resistor, R-74 and chassis.
TRANS. POWER switch to ON. depress the Microphone button. See figure
4--17.

VTVM should indicate -40 to -70 volts d-c grid bias, if oscillator is
supplying proper excitation to PA grid circuit.

Defective oscillator tube or circuit components defective relay K-53;
defective PA tubes; open R-74; low voltage on oscillator.

2.

Set switch on TS-58 to position 4. Depress the Microphone button.

TS-58 meter should read 32-46 (16 to 23

ma. oscillator plate current.)

Same as above; oscillator not oscillating; open R-68, shorted
C-58A.

3.

Tune transmitter FREQUENCY

dial to calibrator crystal frequency. Depress the Microphone
button.

Maximum shadow angle on the "Magic

Eye" tube screen as the FREQUENCY

dial is rotated to the crystal frequency.

Same as above; defective "Magic Eye" tube; defective crystal; no or
low

voltages.

Figure 4-12. Typical Transmitter, Bottom View

Figure 4-13. Modulator, Type MD-7/ARC-5, Bottom
View

Figure 4-14. Typical MD-7/ARC-5 Modulator

Figure 4-15. Transmitter and Modulator Test
Points

Figure 4-16. Diagram

Figure 4-17. Oscillator Check Points
4--16. FINAL AMPLIFIER.

(Follow chart below.)

STEP

TEST POINT

TEST EQUIPMENT CONTROLS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL INDICATION

1.

Emission switch to CW. Power switch to ON. Set COUPLING

control to zero. Set the TS-58 switch to position 5. Press the

Microphone button. (See figure 4--19.)

TS-58 meter indicates l0 (25 ma final PA plate current.)

HIGH CURRENT: Poor tracking, refer

to ALIGNMENT section, paragraph

3--5; defective tubes or other circuit components in PA; shorted
capacitor

C-72.

NO CURRENT: Defective relay K-53; defective PA tubes; no plate or
screen voltage on PA tubes.

2.

Same as Step 1, except set TS-58 switch to position 2.

TS-58 meter indicates 34-38 (170-190 volts PA screen voltage.)

HIGH VOLTAGE: Defective PA tubes; defective R-89.

LOW VOLTAGE: Insufficient excitation; refer to TROUBLE ISOLATION,
OSCILLATOR section, paragraph

4--14; shorted screen by-pass capacitors C-64, C-75, C-71; open screen
resistors R-90, R-94, R-81 and R-89; open secondary windings on modulation
transformer T-58.

3.

Same as Step I, advance COUPLING control to 3. Adjust ANT INDUCTANCE
control for maximum PA plate current and maximum ANT current.

ANT current of over 2.0 amperes. TS-58

reading of 60 to 80 (150 to 200 ma final

PA plate current.)

Same as above: if normal indications

are obtained in Steps 1 and 2, but not Step 3, relay K-54 (K-55 also,
if used) may be defective. Sliding roller contact on ANT TUNING coil may
be dirty, corroded, and not making good electrical
contact.

4--17. MODULATOR.
(Follow chart below.)
4--18. PRELIMINARY INSTRUCTIONS: Set up
equipment as illustrated in Figure 4--19, with the transmitter and associated
equipment connected as in PERFORMANCE section. By means of shielded cable,
connect from vertical input terminals of scope to indicated TEST POINT. Connect
output meter across vertical input terminals of the scope. If Weston model 695
output meter is used, set it to "0" decibel range. (If Daven model OP-182 is
used set the power multiplier switch to "1" position and set the impedance
multiplier switch Phantom Antenna for maximum antenna current, on CW emission,
as described in the PERFORMANCE section, TRANSMITTER TRACKING AND LOADING,
paragraph 2-30, Steps 1, 2, and 3. Plug a pair of headphones into the headphone
jack on the receiver control box, or receiver rack. A loud audio tone or whistle
should be heard during each Step given below.

STEP

TEST POINT

TEST EQUIPMENT CONTROLS

NORMAL INDICATION

POSSIBLE CAUSES OF ABNORMAL INDICATION

1.

Emission switch to VOICE. Ro-

tare COUPLING control to zero,

key transmitter, and advance

COUPLING control clockwise

until Phantom Antenna meter

reads 1.6 amperes. Set emission

switch to TONE and key transmitter.

Antenna current should increase from

1.6 to 1.9 amperes, when going from

VOICE to TONE emission. Audio sine

wave pattern scope output meter

should read +2 decibels. (1.5 mw on

OP-182.)

If no or low output meter reading, tone

oscillator is defective. If normal output

meter reading, but no increase in an-

tenna current, modulator tubes and cir-

cuit components are defective.

2.

Set emission switch to VOICE.

Plug microphone into MIC. jack,

J-73, on front of modulator. Set

output meter on + 12 db range

(power multiplier switch to 100

on OP-182). Press microphone

button and whistle loud, sustained

tone of constant pitch into micro

phone.

Antenna current should increase from 1.6 to 1.9 amperes when mike is
Whistled into. Output meter should indicate + 14 db (+ 2 db, with 0 db now
being + 12 db) on loud sustained whistle. (OP-182 should read I000 mw).
Approximate audio sine wave pattern on 'scope.

Defective modulator tubes and circuit

components. defective C-29/ARC-5 control box. Defective receptacles
on

modulator. Defective microphone circuit. Improper or no voltages on
modulator tubes. Defective modulation transformer T-58. Measure all
voltages and make continuity measurements.

3.

Set emission switch to TONE. Key

transmitter.

Antenna current should rise to 1.9 amperes. Output meter should read +
14 db (+ 2 db, with 0 db being + 12 db).

(OP-182 meter should read 700 milliwatts.)

Same as above. Replace modulator

tubes with known good ones. Check

for shorted capacitors and open resistors. Check continuity from
modulator to transmitter.

Figure 4-18. Final Amplifier Check Diagram

Figure 4-19. Modulator Check
Diagram